Posts

Days 7 and 8

Image
 I feel like a contestant on the Great Pottery Thrown Down and running out of time. I'll miss the last week as I've got to go to a conference so I'm not sure if I'll get everything finished. The vase has dried out enough for me to start to add the decorations. Despite being a bit of a rush, it's starting to look quite good. I'm just hoping that I don't mess it up with the glazing and it doesn't explode in the kiln. The petals and small cuts in the head are most likely to fall off I suppose. I've dabbed on a grey underglaze using a sponge to try and reduce the amount of brush marks.  There is not a lot else I can do until it's fired. When it is all fired and glazed I want to add some gold leaf to highlight some of the tips (and because I like shiny things!)

Day 6 - starting the make

Image
We had a break for half term and I've realised that I'll miss the last session so I might be short of time but we'll see. I've started to form the body of the pot. I used a high-tech cardboard tube and some scrunched up paper to stop it sagging while it dries. The bit I was worried about, the physical join between the two slabs, went well and should be invisible once its glazed and decorated. Less impressive was the fact that one of the slabs was the wrong way around. It required some trimming to make it look something like. At least with it being a large piece there was plenty of clay to play with. The moulds are working out ok as well. The mould for the head worked and I played around with some decorations so I'm ready to go next week. The petals were just to flimsy and I might as well extrude them instead. So long as I shape them a big by hand that should be reasonably consistent. The decoration on the left looks like something you'd use for testing in a wind...

Day 5 - big pieces of clay

Image
The vase I plan on making is somewhat bigger than it looks in a cabinet in the museum. I made a cardboard model of it to act as a template and get an idea of where to place the decoration. I then spent the rest of the session trying to make a large enough sheet of clay for it. Its too big for the roller. In the end, I had to make two slabs and I'll join them next week. When I was doing this, I wanted to make something that was a challenge but achievable. I just hope it doesn't all fall apart in the kiln.

Day 4 - planning and stuff

Image
This week was fairly easy on the techniques. The first job was to try and the sprig mold I made last week. It turns out I left parts of the mold undercut so the plaster was a bit damaged when it was taken out. I then had to cut away the remaining undercuts on the plaster before I could try and use it. The leaves came out ok(ish) in the end. If I was doing it again, apart from being more careful with the undercutting, I'd do the leaves and stem separately. It wasn't really possible to get them all out of the mold in one go. One lightly damaged mold Leaves from the mold The second job was putting some oxides on  the clays tiles that had now been fired. As I had no real clue how these would turn it, it was a question of painting on the oxides, wiping some off with a sponge and hoping for the best. Finally the interesting bit was starting to plan how I'll use some of these techniques in a piece. So far I've decided I like the gold-on-grey on a piece by Evelyn De Morgan  and...

Day 3 - Slip Transfers and Sprig Molds

Image
 The first of this week's efforts was slip printing. You paint layers of coloured slip onto tissue paper and then slap the paper onto a slab of wet clay. After a bit of pressing and praying, you can peel off the paper to reveal your masterpiece. Jason Bige Burnett makes this look easy. I'm not sure if I'm inspired by this or depressed. Either way, for my first attempt I tried a false-coloured teasel. Teasels are all a bit brown so I thought I would brighten it up a bit. I seem to have made some weird strawberry-teasel hyrbid. The second attempt came out better and I can start to see how the technique could be effective. A teaselberry! Attempt two The second technique was making a sprig mold. We had to create a model of what we wanted and take a plaster cast to produce a negative. From that we can copies of the original clay model. I used some mahonia leaves to cut out an outlines of the leaves in clay and used that to make the mold. It looked as much like holly as mahonia ...
Image
 Day 2 Day 2 was a bit more craft and a bit less art. We had to take our previous drawing and carve out a design based on it onto a small piece of lino. My first attempt wasn't cut deeply enough into the lino so I had to re-cut the design a bit deeper. Attempt 1 Attempt 2 Then we used that to print an image onto paper and impress an image onto clay to make a coupe of small tiles. The printing was fairly straight forward. You had to roll the ink well, to spread it around and warm it up, before rolling it onto the lino and pressing it to the paper. Clay tiles Lino print What surprised by that the fine marks on the lino actually printed quite well and didn't fill with ink. May be I could've made the cutting finer but the chunky cuts fit the stylised design. I want to see clay tiles carry the details compared to the prints.